Woods Equipment BSE5 Manual do Utilizador

OPER ATOR'S MANUALBOX SCRAPER&REAR BLADEMAN0561 (Rev. 5/1/2009)HERITAGE™Tested. Proven. Unbeatable.BSE4BSE5RBE4RBE5

10 OperationMAN0561 (8/25/2006) Figure 2. Top Link Connected - Box Scraper Figure 3. Top Link Connected - Rear BladeOPERATING TECHNIQUES - BOX SCRAPER

Operation 11MAN0561 (8/25/2006)OPERATING TECHNIQUES - REAR BLADEAdjusting Top LinkLevel the A-frame and boom with 3-point connectinglinks and top link

12 MaintenanceMAN0561 (8/25/2006)MAINTENANCEThe information in this section is written for operatorswho possess basic mechanical skills. If you need h

Maintenance 13MAN0561 (8/25/2006)Replacing Scarifier Tooth1. Remove scarifier shank (1) from the scarifier bar.2. Remove the worn tooth by driving a c

14 AssemblyMAN0561 (8/25/2006)ASSEMBLYDEALER SET-UP INSTRUCTIONSAssembly of this Box Scraper and Rear Blade is theresponsibility of the WOODS dealer.

Assembly 15MAN0561 (8/25/2006)Assemble Box Scraper1. Place the A-frame hitch over the threecorresponding holes on the inside of the scraperframe as sh

16 AssemblyMAN0561 (8/25/2006)REAR BLADERemove Components from Shipping Configuration1. Remove nut (5), washer (6) and pull pin (7) fromtop of blade.2

Dealer Check Lists 17MAN0561 (8/25/2006)DEALER CHECK LISTSPRE-DELIVERY CHECK LIST(DEALER’S RESPONSIBILITY)Inspect the equipment thoroughly after assem

18 PartsMAN0561 (8/25/2006)BSE4 / BSE5 BOX SCRAPER6814297106712 - COMPLETE DECAL SET5REF PART QTY DESCRIPTION1 1027927 - Top link mount - left hand 2

Parts 19MAN0561 (8/25/2006)RBE4 / RBE5 REAR BLADE7135648 - COMPLETE DECAL SETREF PART QTY DESCRIPTION1 ---------- - Hitch main frame (not sold separat

2 IntroductionGen’l (Rev. 3/5/2010)TO THE DEALER:Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read man

20 AppendixBolt Torque & Size Charts (Rev. 3/28/2007)BOLT TORQUE CHARTAlways tighten hardware to these values unless a different torque value or t

Appendix 21Bolt Torque & Size Charts (Rev. 3/28/2007)BOLT SIZE CHARTNOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for

F-3079 (Rev. 1/12/2011)Woods Equipment Company2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 USA800-319-6637 tel800-399-6637 f

F-8494 (Rev. 6/23/2005)WARRANTY(Replacement Parts For All Models Except Mow’n MachineTMZero-Turn Mowers and Woods BoundaryTM Utility Vehicles)Woods Eq

Woods Equipment Company2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com©20

Introduction 3MAN0561 (8/25/2006)TABLE OF CONTENTSINTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 IntroductionMAN0561 (8/25/2006)SPECIFICATIONSGENERAL INFORMATIONBSE4 BSE5 RBE4 RBE5Overall Width 48" 60" 48" 60"Weight 309 lbs.

Safety 5Heritage Landscape (8/8/2006)TRAINING Safety instructions are important! Read allattachment and power unit manuals; follow allsafety rules an

6 SafetyHeritage Landscape. (8/8/2006)(Safety Rules continued from previous page) Always sit in power unit seat when operatingcontrols or starting en

Safety 7MAN0561 (8/25/2006) 1 - Serial Number Plate2 - 55121MODEL NO. SERIAL NO.Woods Equipment CompanyOregon, Illinois, U.S.A.BE CAREFUL!Use a clean,

8 SafetyMAN0561 (8/25/2006)SAFETY & INSTRUCTIONAL DECALSATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!Replace Immediately If Damaged!CRUSHING A

Operation 9MAN0561 (8/25/2006)OPERATIONThe operator is responsible for the safe operation ofthis equipment. The operator must be properly trained.Oper